Many people think that the cement automatic mixer is not used during this period of time, so there is no need to do any preventive work. In fact, it is not the case. Three things should be done so that the equipment can not go wrong.

　　防腐蝕

　　Corrosion resistant

　　水泥攪拌車工作完成后，要清理外部污垢，清理工作機構中的濃縮飼料和雜物，必要時用水或油清洗，需要擦干凈再涂油，建議貼貼紙，減少接觸空氣氧化的機會。復雜、高精度的設備建議存放在室內陰涼、干燥、自然通風的地方；簡單的設備如螺旋鉆和給料器也可以露天存放，但應放置在高處、干燥且不受影響的地方建議搭棚遮蓋陽光照射的位置；任何與地面直接接觸的備件應由木板或磚塊支撐；脫落的保護漆應重新粉刷。

　　Cement mixer after the completion of the work, to clean up the external dirt, clean up the concentrated feed and debris in the work mechanism, when necessary, clean with water or oil, need to wipe and then oil, it is recommended to paste stickers, reduce the opportunity to contact air oxidation. Complex and high-precision equipment is recommended to be stored indoors in a cool, dry and naturally ventilated place. Simple equipment such as auger and feeder can also be stored in the open air, but should be placed in a high, dry and unaffected place. Any spare parts in direct contact with the ground shall be supported by wooden boards or bricks; Peeling protective paint should be repainted.

　　反腐敗

　　The anti-corruption

　　腐爛的木材零件由于微生物和雨、風、日光的作用而腐爛、開裂和變形。一個合理有效的儲存方法是在木材的外表面涂漆并放置在干燥的地方。可以暴露在陽光和雨水中。紡織品，如帆布傳送帶，如果存放不合理，很容易發霉。此類產品不應放置在露天。需要將它們取出、清洗干凈并晾干，然后存放在室內干燥的地方，可以防止蚊蟲和嚙齒動物的滋生。

　　Decaying wood parts decay, crack and deform due to microorganisms and the action of rain, wind and sunlight. A reasonable and effective storage method is to paint the outside surface of the wood and store it in a dry place. Can be exposed to sunlight and rain. Textiles, such as canvas conveyor belts, can easily become moldy if not properly stored. Such products should not be placed in the open air. They need to be removed, washed and dried, and stored indoors in a dry place to prevent mosquitoes and rodents from breeding.

　　抗變形

　　Resistance to deformation

　　彈簧、傳動帶、長刀桿、輪胎等備件會因長期受力或放置不合理而發生塑性變形。因此，應在框架下增加適當的支撐點；使輪胎不承載負載；所有被夾緊或拉開的彈簧都需要松開；將傳動帶卸下并妥善存放在室內；一些容易變形的拆卸部件，如長工具桿，應平放或垂直懸掛；輪胎、播種管等備件在存放時應防止擠壓變形。

　　Spring, transmission belt, long knife bar, tires and other spare parts will be plastic deformation due to long-term stress or improper placement. Therefore, appropriate support points should be added under the framework; Make the tire not load bearing; All springs that are clamped or pulled need to be released; Remove the belt and store it indoors; Some easy to deform disassembly parts, such as long tool bars, should be flat or vertical suspension; Spare parts such as tires and seeding pipes should be prevented from extrusion deformation when stored.

　　以上就是水泥自動攪拌車閑置時要做好的預防工作，還有什么地方不明白的，歡迎您點擊http://m.top2010.cn這個網址進行咨詢。

　　The above is the prevention work to be done when the cement automatic mixer is idle. If there is any place that you do not understand, you are welcome to click on the website http://m.top2010.cn for consultation.